The SpeakerCraft CB and CB-X connecting block components
provide a convenient way to connect multiple speaker pairs to
a single amplifier. The components are designed to be used in
conjunction with SpeakerCraft's VSI-60 impedance matching
volume controls which are connected to each pair of speakers.
Multiple VSI-60 controls can be "home run" to the CB and CB-X,
which in turn is connected to an amplifier.
The CB serves as the primary component (accommodating up
to 4 pairs of speakers). Each CB-X also accommodates up to 4
pairs of speakers. CB-X components can be added to the CB,
and other CB-X components, to allow for additional inputs.
Wiring the CB & CB-X
Caution: Please make sure your amplifier or receiver is off before proceeding.
The CB and CB-X feature SpeakerCraft's simple connect system. This system is quicker and more secure than
other methods and eliminates the need for turning small screws.
For best results strip all wire no more than 1/4" from the end. Push the wire completely into the opening on
the connector then depress the lever using your finger or screwdriver. This will secure the wire (see Figure
#1). If you need to remove the wire simply lift the lever. This can be done with your finger, but you may find it
easier to use a screwdriver or similar tool. With the lever lifted, pull the wire out.
1. Connect the Amplifier: Connect the amplifier's or receiver's speaker outputs to the connector labeled
"amplifier", please observe proper channel and polarity of the connections (+ from the amplifier to + input on
the control, left channel out to the "L" side of the connector marked "amplifier" on the selector).
2. Connect the Speakers: Connect the speaker wires to the terminals labeled "Speakers", please observe
proper channel and polarity of the connections (+ from the speaker to + input on the control, left channel
from the speaker to the "L" side of the connector marked "speaker" on the selector).
Caution: Each speaker pair should also be connected to a SpeakerCraft impedance matching volume control,
such as the VSI-60. Please refer to the VSI-60 instructions for proper wiring of the volume control. Failure to
use an impedance matching volume control could result in damage to your amplifier or receiver.
Adding CB-X Expansion Components:
To connect more than 4 pairs of speakers to the CB you will need to add CB-X expansion components. Each
CB-X allows the connection of an additional 4 pair of speakers. To connect the CB-X to the CB simply plug the
pin end of the CB-X, marked "input" into the socket of the CB marked "Expansion".
AMPLIFIER
L+ L- R- R+
OPEN
POSITION
CLOSED
POSITION
1/4"
STRIP WIRE
TO 1/4"
Figure #1
CB,CB-X
Peržiūrėkite vadovą SpeakerCraft CB-X čia, nemokamai. Šis vadovas priskiriamas kategorijai neklasifikuojama ir buvo įvertintas 1 žmonių, kurių vidurkis a 5.7. Šis vadovas pateikiamas šiomis kalbomis: Anglų. Ar turite klausimą apie SpeakerCraft CB-X ar Jums reikia pagalbos? Užduokite savo klausimą čia
Reikia pagalbos?
Ar turite klausimų apie SpeakerCraft , kurio atsakymo vadove nera? Užduokite savo klausimą čia. Pateikite aiškų ir išsamų problemos ir savo klausimo aprašymą. Kuo geriau apibūdinsite savo problemą ir klausimą, tuo lengviau kiti SpeakerCraft savininkai galės pateikti tinkamą atsakymą.
Reikia pagalbos?
Ar turite klausimų apie SpeakerCraft , kurio atsakymo vadove nera? Užduokite savo klausimą čia. Pateikite aiškų ir išsamų problemos ir savo klausimo aprašymą. Kuo geriau apibūdinsite savo problemą ir klausimą, tuo lengviau kiti SpeakerCraft savininkai galės pateikti tinkamą atsakymą.
Klausimų skaičius: 0