Honeywell RTH230B vadovą

Honeywell RTH230B
9.2 · 2
PDF vadovas
 · 4 puslapiai
Anglų
vadovasHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Peržiūrėkite vadovą Honeywell RTH230B čia, nemokamai. Šis vadovas priskiriamas kategorijai termostatas ir buvo įvertintas 2 žmonių, kurių vidurkis a 9.2. Šis vadovas pateikiamas šiomis kalbomis: Anglų. Ar turite klausimą apie Honeywell RTH230B ar Jums reikia pagalbos? Užduokite savo klausimą čia

Reikia pagalbos?

Ar norite paklausti apie Honeywell , bet atsakymo instrukcijoje nėra?

  • Gaukite naujienas apie sprendimus
  • Gaukite atsakymus į savo klausimus

Klausimas ir atsakymas

Klausimų skaičius: 0

Honeywell RTH230B yra reguliatorius, skirtas valdyti kambario temperatūrą. Šis termostatų modelis buvo sukurtas taip, kad jo naudojimas būtų paprastas ir patikimas, ir paprastas montavimas, kuris tinka daugumai jūsų kurių namų schemų. Jis suteikia galimybę išjungti šildymą arba vėsinimą, kai nėra namuose, kad būtų taupoma energija. Honeywell RTH230B yra neprogramuojamas termostatų modelis, kuris leidžia reguliuoti tam tikras temperatūras pasirinktame laiko intervale. Šis termostatų modelis yra lengvai naudojamas ir yra peržiūrimas, kuris leidžia pamatyti, kokia temperatūra yra valdoma, ir ją lengvai reguliuoti. Rekomenduojama naudoti šį termostatą kvadratinėje arba stačiakampėje patalpoje, kurioje nėra daug kraštų. Be to, Honeywell RTH230B turi perkeliamą pamatą, leidžiantį jums perkelti termostatą kitur, be reikalo montuojant naujas laikiklius ant sienos. Honeywell RTH230B yra patvarus ir ilgaamžis, o jo matmenys: 2,25 colių x 4,8 colių x 3,75 colių.

Bendra informacija
Prekės ženklasHoneywell
ModelisRTH230B
Produktastermostatai
KalbaAnglų
Failo tipasVartotojo vadovas (PDF)

Neradote atsakymo į savo klausimą vadove? Atsakymą į savo klausimą galite rasti žemiau esančiuose DUK apie Honeywell RTH230B.

Kur geriausia pastatyti termostatą?

Geriausia vieta termostatui yra kambarys, kuriame praleidžiate daugiausiai laiko, daugeliu atvejų svetainė ar virtuvė. Pastatykite termostatą maždaug pusantro metro virš grindų, ne saulėje ir ne ant išorinės sienos.

Kas yra negyva termostato juosta?

Jei jūsų termostatas turi negyvą juostą, jūsų įrenginys yra tarsi „ramybės būsenoje“. Termostatas įsijungia tik tada, kai, pavyzdžiui, skirtumas nukrypsta nuo nustatytos kambario temperatūros daugiau nei 2 ˚C.

Kokia yra ideali kambario temperatūra?

Dauguma žmonių mano, kad ideali kambario temperatūra yra nuo 19 iki 22 laipsnių Celsijaus.

Ar Honeywell RTH230B vadovas yra prieinamas Lietuviai?

Deja, neturime prieinamo Honeywell RTH230B vadovo Lietuviai. Šis vadovas yra prieinamas Anglų.

Ar jūsų klausimas nėra įtrauktas į sąrašą? Užduokite savo klausimą čia

Jokių rezultatų