Equip 650201 vadovą

Equip 650201
7.3 · 1
PDF vadovas
 · 2 puslapiai
Anglų
vadovasEquip 650201
LCD TV WALL MOUNT BRACKET

TILTING

Universal | 650201

Features

l Supports 58 ~ 94cm (23” ~ 37”) Flat Panel Display
l Distance from TV to Wall: 46mm
l Flexible Adjustment with 0º ~ -10º Tilt
l VESA Mount Standards: Maximum 400 x 200mm
l Hole Pattern: Maximum 420mm Wide and 230mm High
l Universal Mounting Pattern
l Bubble Level Integrated
l Load Capacity: Maximum 75kg (165lbs)
WARNING!
Make sure that any listed parts are not missing or defective. Improper installation would result in personal
injury or damage to equipment. If you have any questions about installation, please visit
http://www.equip-info.net for more assistance.
Hardware Kit
Note: Any of the hardware in kit will be required. Other joint parts are forbidden.

INSTALLATION

Mount Wall Plate on the Wall - The product is designed for mounting on solid brick, concrete or hard wood
batten/studs wall, but plasterboard or paneled wall is not allowed.
(a) Solid Brick, Concrete Block Wall - Use the wall plate
a
as a template to mark 6 holes location on the
wall, three in the top row slots and three more in the bottom row. Make sure these holes are level and there
is at least 200mm between any two holes. Drill these holes with a 10mm masonry bit to at least 60mm in
depth. Insert a concrete anchor
e
into each of these holes. Attach the wall plate to the wall using 6 lag
bolts
d
and 6 lag bolt washers
g
.
(b) Hard Wood Batten/Stud Wall - The wall plate
a
must be mounted to two wood studs. Use a high
quality stud sensor to locate three adjacent studs. It is a good idea to verify where the studs are located
with an awl or thin nail shown in diagram 1-A. Drill a 3mm deep hole at the desired height in each stud using
a 4mm drill bit. Use the wall plate
a
as a template to mark the location of the second hole in each stud.
Pre-drill these holes using the 4mm drill bit as well. Attach the wall plate to the wall using the 4 lag bolts
d
and 4 lag bolt washers
g
. Make sure the wall plate is oriented so the flat surface in the center of the plate in
against the wall shown in diagram 1-B. Note: Do not use any concrete ancher when you mount the bracket
onto hard wood wall.
Mount the TV Rails on the Back of Your Display and Install - Make sure the two TV rails
b
are
mounted at an equal distance from the top of the TV and as close to the center as possible as shown in
diagram 2-A. Knobs should face the outside of the television. Plastic spacers
h
are provided to be used
with M4, M5, M6 and M8 mount screws on TV with curved or recessed back panel as shown in diagram 2-B.
If you mount the TV rails to a television with flat back, you will not need a plastic spacer as shown in diagram
2-C. Make sure these screws are right! Some TVs have shallow threaded inserts; so we have provided 4
extra washers if the provided screws are too long.

Hang the TV on the Wall Plate and Adjust - First hook the TV rails over the top of the wall plate
a
in
diagram 3-A. Then tighten the safety screws on the bottom of TV rails
b
in diagram 3-B. You can adjust
your TV down to 10 degrees at maximum: first loosen one knob, second loosen the other knob and then
adjust the TV whichever degree you want. Finally tighten the two knobs.

s

Peržiūrėkite vadovą Equip 650201 čia, nemokamai. Šis vadovas priskiriamas kategorijai Plokščiojo ekrano atrama ir buvo įvertintas 1 žmonių, kurių vidurkis a 7.3. Šis vadovas pateikiamas šiomis kalbomis: Anglų. Ar turite klausimą apie Equip 650201 ar Jums reikia pagalbos? Užduokite savo klausimą čia

Reikia pagalbos?

Ar turite klausimų apie Equip , kurio atsakymo vadove nera? Užduokite savo klausimą čia. Pateikite aiškų ir išsamų problemos ir savo klausimo aprašymą. Kuo geriau apibūdinsite savo problemą ir klausimą, tuo lengviau kiti Equip savininkai galės pateikti tinkamą atsakymą.

Klausimų skaičius: 0

Bendra informacija
Equip
650201 | 650201
Plokščiojo ekrano atrama
4015867159392
Anglų
Vartotojo vadovas (PDF)
Konstrukcija
Produkto spalvaJuoda
SertifikavimasRoHS
Korpuso medžiagaPlienas
Svoris ir matmenys
Svoris2000 g
Plotis450 mm
Aukštis270 mm
Montavimas
Maksimalus svoris (tūris)75 kg
Montavimo sąsajos suderinamumas (min.)400 x 200 mm
Montavimo sąsajos suderinamumas (maks.)400 x 200 mm
Montavimo tipasSiena
Kitos savybės
Paketo matmenys (WxDxH)496 x 226 x 60 mm
Ekrano dydžio suderinamumas23 - 37 "
Pakuotės duomenys
Paketo svoris2500 g
Ergonomija
Posvyrio kampo intervalas-10 - 0 °
Rodyti daugiau

Neradote atsakymo į savo klausimą vadove? Atsakymą į savo klausimą galite rasti žemiau esančiuose DUK apie Equip 650201.

Ar jūsų klausimas nėra įtrauktas į sąrašą? Užduokite savo klausimą čia

Jokių rezultatų